Endress+Hauser Micropilot S FMR540 Operating Instructions Manual Download Page 62

Page: 62 / 80

Trouble-shooting

Micropilot S FMR540 4 to 20 mA HART

Hauser

Trouble-shooting

9.1

Trouble-shooting instructions

L00-FMR540xx-19-00-00-en-005

Instrument does
not respond

Check voltage and
compare it with the
specifications on the
nameplate.

Connect the
correct voltage

Instrument works?

Ready

Check the polarity
of the voltage.

Check power connection
to electronic board

Correct the polarity

Connect plug

Instrument works?

Ready

Values on display
invisible

Yes

Not ok

Check plug contact
of the display.

Connect the plug
correctly

Correct configuration

Display works?

Ready

Yes

Not ok

Yes

Micropilot S FMR540 -Trouble Shooting

Output current between
3.6 …22mA ?

Contrast:

F O

The display is possibly defective.
Contact Hauser Service

Yes

Output current
< 3,6 mA ?

Check cabling

Correct the
cabling

Current is ok?

Ready

Yes

Possibly defective electronics
Contact E+H Service

HART
communication
does not
function

Is the communication
resistor installed
according to the
OM?

Install the resistor
(see the OM)

Communication ok?

Ready

Yes

Connect the
Commubox
(see the OM)

Communication ok?

Ready

Set the switch
correctly

Communication ok

Ready

Contact Hauser Service

Yes

Not ok

Is the switch on the
Commubox for
selecting HART/Intensor
in the correct position?

Is the Commubox
connected according
to the OM?

Communication
via Service adapter

does not function

Instrument
measures
incorrectly

Check configuration
of COM port on PC

Check basic setup

Proceed according
to section
'Trouble shooting’ in OM

Repeat
basic setup

Not ok

Yes

Communication ok?

Measurement ok?

Summary of Contents for Micropilot S FMR540

















































































Search results

Summary of Contents for Micropilot S FMR540

Reviews:

Related manuals for Micropilot S FMR540

Brands by name

Popular brands

Endress+Hauser Micropilot S FMR540, Operating Instructions Manual

Search results

Summary of Contents for Micropilot S FMR540

Reviews:

Related manuals for Micropilot S FMR540

Brands by name

Popular brands