Endress+Hauser Micropilot FMR56 Operating Instructions Manual Download

Page: 181 / 198

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

Operating menu

Hauser

181

Electronic temperature

Navigation

 Diagnostics → Measured val. → Electronic temp.

Description

Displays the current temperature of the electronics.

Additional information

The unit is defined in the

Temperature unit

parameter.

17.4.5 "Analog input 1 to 5" submenu

There is an

Analog inputs

submenu for every AI block of the device. The AI block is used

to configure the measured value transmission to the bus.

Only the most basic properties of the AI block can be configured in this submenu. For

a detailed configuration of the AI blocks refer to the

Expert

menu.

Navigation

 Diagnostics → Analog inputs → Analog input 1 to 5

Block tag

Navigation

 Diagnostics → Analog inputs → Analog input 1 to 5 → Block tag

Description

Defined to be unique throughout the control system at one plant site. The tag may be

changed using the FB_Tag service.

Factory setting

Channel

Navigation

 Diagnostics → Analog inputs → Analog input 1 to 5 → Channel

Description

Select the process variable.

Selection

• Uninitialized

• Level linearized

• Absolute echo amplitude

• Distance

• Electronic temperature

• Relative echo amplitude

• Analog output adv. diagnostics 1

• Analog output adv. diagnostics 2

• Terminal voltage

Factory setting

Uninitialized

Summary of Contents for Micropilot FMR56







































































































































































































Search results

Summary of Contents for Micropilot FMR56

Reviews:

Related manuals for Micropilot FMR56

Brands by name

Popular brands

Endress+Hauser Micropilot FMR56, Operating Instructions Manual

Search results

Summary of Contents for Micropilot FMR56

Reviews:

Related manuals for Micropilot FMR56

Brands by name

Popular brands