Endress+Hauser Micropilot FMR56 Operating Instructions Manual Download

Page: 180 / 198

Operating menu

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

180

Hauser

17.4.4 "Measured values" submenu

Navigation

 Diagnostics → Measured val.

Distance

Navigation

 Diagnostics → Measured val. → Distance

Description

Displays the measured distance D between the reference point (lower edge of the flange or

threaded connection) and the level.

Additional information

A0019485

 44

Distance for bulk solid measurements

The unit is defined in the

Distance unit

parameter (→  127).

Level linearized

Navigation

 Diagnostics → Measured val. → Level linearized

Description

Displays linearized level.

Additional information

The unit is defined by the

Unit after linearization

parameter →  147.

Terminal voltage 1

Navigation

 Diagnostics → Measured val. → Terminal volt. 1

Description

Dipslays terminal voltage at the current output.

Summary of Contents for Micropilot FMR56







































































































































































































Search results

Summary of Contents for Micropilot FMR56

Reviews:

Related manuals for Micropilot FMR56

Brands by name

Popular brands

Endress+Hauser Micropilot FMR56, Operating Instructions Manual

Search results

Summary of Contents for Micropilot FMR56

Reviews:

Related manuals for Micropilot FMR56

Brands by name

Popular brands