Endress+Hauser Micropilot FMR56 Operating Instructions Manual Download

Page: 178 / 198

Operating menu

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

178

Hauser

17.4.3 "Device information" submenu

Navigation

 Diagnostics → Device info

Device tag

Navigation

 Diagnostics → Device info → Device tag

Description

Enter tag for measuring point.

Factory setting

FMP5x

Serial number



Navigation

 Diagnostics → Device info → Serial number

Description

Displays serial number of the device.

Additional information

Uses of the serial number

• To identify the device quickly, e.g. when contacting Hauser.

• To obtain specific information on the device using the Device Viewer:

www.endress.com/deviceviewer

The serial number is also indicated on the nameplate.

Firmware version

Navigation

 Diagnostics → Device info → Firmware version

Description

Indicates the installed Firmware version.

User interface

xx.yy.zz

Additional information

For firmware versions differing only in the last two digits ("zz") there is no difference

concerning functionality or operation.

Device name

Navigation

 Diagnostics → Device info → Device name

Description

Displays device name.

Summary of Contents for Micropilot FMR56







































































































































































































Search results

Summary of Contents for Micropilot FMR56

Reviews:

Related manuals for Micropilot FMR56

Brands by name

Popular brands

Endress+Hauser Micropilot FMR56, Operating Instructions Manual

Search results

Summary of Contents for Micropilot FMR56

Reviews:

Related manuals for Micropilot FMR56

Brands by name

Popular brands