manualshive.com logo in svg

Endress+Hauser Micropilot FMR56, Operating Instructions Manual

The Endress+Hauser Micropilot FMR56 is a state-of-the-art level transmitter featuring advanced technology and reliable performance. Ensure safe usage by downloading the free user manual, packed with essential safety instructions. Download it for free from our website and unleash the full potential of this remarkable product.

Share
Download
background image

Operating menu

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

158

Hauser

Switch-on value

Navigation

 Setup → Advanced setup → Switch output → Switch-on value

Prerequisite

Switch output function (→   156)

 = 

Limit

Description

Enter measured value for the switch-on point.

User entry

Signed floating-point number

Factory setting

0

Additional information

The switching behavior depends on the relative position of the 

Switch-on value

 and

Switch-off value

 parameters:

Switch-on value > Switch-off value

– The output is closed if the measured value is larger than 

Switch-on value

.

– The output is opened if the measured value is smaller than 

Switch-off value

.

t

t

A

B

C

D

  A0015585

A

Switch-on value

B

Switch-off value

C

Output closed (conductive)

D

Output opened (non-conductive)

Switch-on value < Switch-off value

– The output is closed if the measured value is smaller than 

Switch-on value

.

– The output is opened if the measured value is larger than 

Switch-off value

.

Summary of Contents for Micropilot FMR56







































































































































































































Reviews:

No comments

Related manuals for Micropilot FMR56

Brands by name

Popular brands

Load more brands