Endress+Hauser Micropilot FMR20 Operating Instructions Manual Download Page 93

Page: 93 / 102

Micropilot FMR20 HART

Operating menu

Hauser

Relative echo amplitude (TV)

Navigation



Setup → Communication → Rel.echoampl(TV)

User interface

Signed floating-point number

Temperature (QV)

Navigation



Setup → Communication → Temperature (QV)

User interface

Signed floating-point number

"Bluetooth configuration" submenu

Navigation

 Setup → Communication → Bluetooth conf.

Bluetooth mode



Navigation



Setup → Communication → Bluetooth conf. → Bluetooth mode

Description

Enable or disable Bluetooth function..

Remark:

Switching to position 'Off' will disable remote access via the app with immediate effect. To

re-establish a Bluetooth connection via the app: Please follow the advices in the manual.

Selection

• Off

• On

Summary of Contents for Micropilot FMR20







































































































Search results

Summary of Contents for Micropilot FMR20

Reviews:

Endress+Hauser Micropilot FMR20, Operating Instructions Manual, Page: 93 / 102

Search results

Summary of Contents for Micropilot FMR20

Reviews: