Endress+Hauser Micropilot FMR20 Operating Instructions Manual Download Page 15

Page: 15 / 102

Micropilot FMR20 HART

Installation

Hauser

A0046282

 4

Nozzle installation

The maximum nozzle length

depends on the nozzle diameter

Please note the limits for the diameter and length of the nozzle.

80 mm (3 in) antenna, installation inside nozzle

• D: min. 120 mm (4.72 in)

• L: max. 205 mm (8.07 in) + D × 4.5

80 mm (3 in) antenna, installation outside nozzle

• D: min. 80 mm (3 in)

• L: max. D × 4.5

5.1.3

Position for installation on a vessel

A0045323

 5

Installation position on a vessel

• If possible install the sensor so that its lower edge is inside the vessel.

• Recommended distance

wall - nozzle outer edge: ~ ¹⁄₆ of the vessel diameter. Under no

circumstances should the device be mounted closer than 15 cm (5.91 in) to the vessel

wall.

• Do not install the sensor in the middle of the vessel.

Summary of Contents for Micropilot FMR20







































































































Search results

Summary of Contents for Micropilot FMR20

Reviews:

Endress+Hauser Micropilot FMR20, Operating Instructions Manual, Page: 15 / 102

Search results

Summary of Contents for Micropilot FMR20

Reviews: