Endress+Hauser magphant Operating Instructions Manual Download Page 22 | Manualshive

Page: 22 / 44

background image

Electrical connection

Magphant

22

Hauser

7.1.4

Preparing the measuring device

NOTICE

Insufficient sealing of the housing!

Operational reliability of the measuring device could be compromised.

‣

Use suitable cable glands corresponding to the degree of protection.

1. Remove dummy plug if present.
2. If the measuring device is supplied without cable glands:

Provide suitable cable gland for corresponding connecting cable.

3. If the measuring device is supplied with cable glands:

Observe requirements for connecting cables →  21.

7.2

Connecting the measuring device

NOTICE

Limitation of electrical safety due to incorrect connection!

‣

Have electrical connection work carried out by appropriately trained specialists only.

‣

Observe applicable federal/national installation codes and regulations.

‣

Comply with local workplace safety regulations.

7.2.1

Connecting the transmitter

‣

Tighten the screw terminals. Recommended tightening torque: 0.5 Nm (0.37 lbf ft)

27

26

25

24

23

2

1

1

2

3

3

4

A0040168

 9

Connecting the transmitter

1

Power supply cable

2

Signal cable

3

Ground terminals for cable shield

4

160 mA fuse, slow-blow

«
...
20
21
22
23
24
...
»

Summary of Contents for magphant













































Reviews:

No comments

Related manuals for magphant

Brand: Vcheck Pages: 31

Brand: Eagletone Pages: 2

Brand: Makita Pages: 2

Brand: Makita Pages: 16

Brand: Jasco Pages: 48

Brand: Rayjet Pages: 81

Clavinova CLP-110

Brand: Yamaha Pages: 46

Clavinova CLP-110

Brand: Yamaha Pages: 46

Brand: Yamaha Pages: 8

Brand: Energic Plus Pages: 12

BML-S1G0-Q71 Series

Brand: Balluff Pages: 20

Brand: Power Measurement Pages: 20

Brand: JUMO Pages: 150

Brand: Hanna Instruments Pages: 28

Stream Line Pro

Brand: Halo Photonics Pages: 45

Stubby LED-1500

Brand: Dive Perfect Pages: 4

Brand: Fluke Pages: 8

Brand: 4iiii Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands