Endress+Hauser Liquiphant FTL64 Operating Instructions Manual Download Page 6

Page: 6 / 64

Basic safety instructions

Liquiphant FTL64

Hauser

Series of steps

1.2.5

Symbols in graphics

A, B, C ...

View

1, 2, 3 ... Item numbers

Hazardous area

Safe area (non-hazardous area)

1.2.6

Registered trademarks

Bluetooth®

The

Bluetooth®

word mark and logos are registered trademarks owned by the Bluetooth

SIG, Inc. and any use of such marks by Hauser is under license. Other trademarks

and trade names are those of their respective owners.

Apple®

Apple, the Apple logo, iPhone, and iPod touch are trademarks of Apple Inc., registered in

the U.S. and other countries. App Store is a service mark of Apple Inc.

Android®

Android, Google Play and the Google Play logo are trademarks of Google Inc.

Basic safety instructions

2.1

Requirements for the personnel

The personnel must fulfill the following requirements to carry out the necessary tasks,

e. g., commissioning and maintenance:

‣

Trained, qualified specialists must have a relevant qualification for the specific function

and task

‣

Are authorized by the plant owner/operator

‣

Are familiar with federal/national regulations

‣

Must have read and understood the instructions in the manual and supplementary

documentation

‣

Follow instructions and comply with conditions

2.2

Intended use

• Only use the device for liquids

• Improper use can pose hazards

• Ensure that the measuring device is free of defects while it is in operation
• Use the device only for media to which the wetted materials have an adequate level of

resistance

• Do not exceed or drop below the relevant limit values for the device

For more details, see the "Technical data" section

See the Technical Documentation

2.2.1

Incorrect use

The manufacturer is not liable for damage caused by improper or non-intended use.

Summary of Contents for Liquiphant FTL64

































































Search results

Summary of Contents for Liquiphant FTL64

Reviews:

Related manuals for Liquiphant FTL64

Brands by name

Popular brands

Endress+Hauser Liquiphant FTL64, Operating Instructions Manual

Search results

Summary of Contents for Liquiphant FTL64

Reviews:

Related manuals for Liquiphant FTL64

Brands by name

Popular brands