Endress+Hauser Liquiphant FTL64 Operating Instructions Manual Download Page 51

Page: 51 / 64

Liquiphant FTL64

Accessories

Hauser

13.4 Protective cover for single compartment housing,

aluminum or 316L

• Material: plastic

• Order number: 71438291

140 (5.51)

32 (1.26)

115 (4.53)

122 (4.8)

A0038280

 45

Protective cover for single compartment housing, aluminum or 316L. Unit of measurement mm (in)

13.5 Plug-in jack

The plug-in jacks listed are suitable for use in the temperature range

–25 to +70 °C (–13 to +158 °F).

Plug-in jack M12 IP69

• Terminated at one end

• Elbowed 90 °

• 5 m (16 ft) PVC cable (orange)

• Slotted nut 316L (1.4435)

• Body: PVC (orange)

• Order number: 52024216

27.5

(1.08)

(1.57)

A0023713

 46

Plug-in jack M12 IP69. Unit of measurement mm (in)

Plug-in jack M12 IP67

• Elbowed 90 °

• 5 m (16 ft) PVC cable (gray)

• Slotted nut Cu Sn/Ni

• Body: PUR (black)

• Order number: 52010285

Summary of Contents for Liquiphant FTL64

































































Search results

Summary of Contents for Liquiphant FTL64

Reviews:

Related manuals for Liquiphant FTL64

Brands by name

Popular brands

Endress+Hauser Liquiphant FTL64, Operating Instructions Manual

Search results

Summary of Contents for Liquiphant FTL64

Reviews:

Related manuals for Liquiphant FTL64

Brands by name

Popular brands