Endress+Hauser Liquiphant FTL64 Operating Instructions Manual Download Page 10

Page: 10 / 64

Mounting

Liquiphant FTL64

Hauser

Storage temperature

–40 to +80 °C (–40 to +176 °F)

Optional: –50 °C (–58 °F), –60 °C (–76 °F)

4.3.2

Transporting the device

• Transport the device to the measuring point in the original packaging

• Hold the device by the housing, temperature spacer, flange or extension pipe

Take suitable measures to protect the coating!

• Do not bend, shorten or extend the tuning fork

A0042422

 2

Handling the device during transportation

Mounting

WARNING

Loss of protection rating if the device is opened in a wet environment.

‣

Only open the device in a dry environment!

Mounting instructions

• Any orientation for device with short pipe up to approx. 500 mm (19.7 in)

• Vertical orientation from above for device with long pipe

• Minimum distance between the fork tip and the tank wall or pipe wall: 10 mm (0.39 in)

Summary of Contents for Liquiphant FTL64

































































Search results

Summary of Contents for Liquiphant FTL64

Reviews:

Related manuals for Liquiphant FTL64

Brands by name

Popular brands

Endress+Hauser Liquiphant FTL64, Operating Instructions Manual

Search results

Summary of Contents for Liquiphant FTL64

Reviews:

Related manuals for Liquiphant FTL64

Brands by name

Popular brands