Endress+Hauser Liquiline To Go CYM290 Operating Instructions Manual Download Page 42

Page: 42 / 64

Oxy Cond

Error and Status Messages

“Sensoface” Messages

The “Sensoface” icon provides information on the sensor condition:

Sensoface Meaning

Sensor is okay

Calibrate the sensor soon

Calibrate or replace the sensor

Info

Message

Info 01

Cal timer expired

Info 02

Sensor wear

Info 03

Bad glass impedance

Info 05

Zero/Slope

Info 06

Response time too long

Info 07

Operating point (ISFET)

Info 08

Leakage current (ISFET)

Info 09

ORP offset

Info 10

Polarization

Info and Help Texts

When an error or status message appears on the screen, proceed as follows to view
the corresponding info or help text:
1)  Press E.
2)  Press the Help softkey.
3)  The help text will be displayed. In most cases, you can remedy the cause of the

error by yourself. Please refer to the following table for possible remedies.

Summary of Contents for Liquiline To Go CYM290

































































Search results

Summary of Contents for Liquiline To Go CYM290

Reviews:

Related manuals for Liquiline To Go CYM290

Brands by name

Popular brands

Endress+Hauser Liquiline To Go CYM290, Operating Instructions Manual

Search results

Summary of Contents for Liquiline To Go CYM290

Reviews:

Related manuals for Liquiline To Go CYM290

Brands by name

Popular brands