Endress+Hauser iTHERM TrustSens TM371 Operating Instructions Manual Download Page 79

Page: 79 / 106

iTHERM TrustSens TM371, TM372

Operating menu and parameter description

Hauser

20 mA value

Navigation

Setup → Upper range value

Expert → Output → 20 mA value

Description

Use this function to assign a measured value to the current value 20 mA.

Factory setting

150 °C

Failure mode

Navigation

Setup → Failure mode

Expert → Output → Failure mode

Description

Use this function to select the signal on alarm level of the current output in an event of an

error.

Options

• High alarm

• Low alarm

Factory setting

Low alarm

14.2 Calibration menu

All the information that describes the self-calibration procedure as well as the online

wizard creating a calibration report.

Number of self-calibrations

Navigation

Calibration → Number of self-calibrations

Description

This counter displays the amount of all executed self-calibrations. It cannot be reset.

Stored self-calibration points

Navigation

Calibration → Stored self-calibration points

Description

Displays the amount of all stored self-calibration points. This device is able to store 350

self-calibration points. As soon as the memory would reach its limit, the oldest self-

calibration point will be overwritten.

Display

0 to 350

Summary of Contents for iTHERM TrustSens TM371











































































































Search results

Summary of Contents for iTHERM TrustSens TM371

Reviews:

Brands by name

Popular brands

Endress+Hauser iTHERM TrustSens TM371, Operating Instructions Manual

Search results

Summary of Contents for iTHERM TrustSens TM371

Reviews:

Brands by name

Popular brands