Endress+Hauser Hart Proline Promag P 500 Operating Instructions Manual Download Page 71

Page: 71 / 210

Proline Promag P 500 HART

Operation options

Hauser

8.3.4

Operating elements

Operating key(s)

Meaning

Minus key

In a menu, submenu

Moves the selection bar upwards in a choose list.

With a Wizard

Confirms the parameter value and goes to the previous parameter.

With a text and numeric editor

Move the entry position to the left.

Plus key

In a menu, submenu

Moves the selection bar downwards in a choose list.

With a Wizard

Confirms the parameter value and goes to the next parameter.

With a text and numeric editor

Move the entry position to the right.

Enter key

For operational display

• Pressing the key briefly opens the operating menu.
• Pressing the key for 2 s opens the context menu including the option for activating the

keypad lock.

In a menu, submenu

• Pressing the key briefly:

– Opens the selected menu, submenu or parameter.
– Starts the wizard.
– If help text is open, closes the help text of the parameter.

• Pressing the key for 2 s for parameter:

If present, opens the help text for the function of the parameter.

With a Wizard

Opens the editing view of the parameter.

With a text and numeric editor

• Press the key briefly: confirm your selection.
• Press the key for 2 s: confirm the entry.

Escape key combination (press keys simultaneously)

In a menu, submenu

• Pressing the key briefly:

– Exits the current menu level and takes you to the next higher level.
– If help text is open, closes the help text of the parameter.

• Pressing the key for 2 s returns you to the operational display ("home position").

With a Wizard

Exits the wizard and takes you to the next higher level.

With a text and numeric editor

Close the editing view without accepting the changes.

Minus/Enter key combination (press the keys simultaneously)

Press the key for 3 s: deactivate the keypad lock.

8.3.5

Opening the context menu

Using the context menu, the user can call up the following menus quickly and directly from

the operational display:
• Setup

• Data backup

• Simulation

Summary of Contents for Hart Proline Promag P 500



















































































































































































































Search results

Summary of Contents for Hart Proline Promag P 500

Reviews:

Endress+Hauser Hart Proline Promag P 500, Operating Instructions Manual, Page: 71 / 210

Search results

Summary of Contents for Hart Proline Promag P 500

Reviews: