manualshive.com logo in svg

Endress+Hauser Hart Proline Promag P 500, Operating Instructions Manual, Page: 57 / 210

Share
Download
Endress+Hauser Hart Proline Promag P 500 Operating Instructions Manual Download Page 57

Proline Promag P 500 HART

Electrical connection

Hauser

57

+

–

  A0029340

Prerequisite: The sensor is installed in the pipe in a way that provides electrical insulation.

1. Connect the two flanges of the pipe to one another via a ground cable.
2. Guide the shield of the signal lines through a capacitor.
3. Connect the measuring device to the power supply such that it is floating in relation

to the protective ground (isolation transformer).

7.5  

Special connection instructions

7.5.1  

Connection examples

Current output 4 to 20 mA HART

4

4...20 mA

5

2

1

3

6

  A0029055

 22

Connection example for 4 to 20 mA HART current output (active)

1

Automation system with current input (e.g. PLC)

2

Cable shield: the cable shield must be grounded at both ends to comply with EMC requirements; observe cable
specifications

3

Connection for HART operating devices →   83

4

Resistor for HART communication (≥ 250 Ω): observe maximum load →   179

5

Analog display unit: observe maximum load →   179

6

Transmitter

Summary of Contents for Hart Proline Promag P 500



















































































































































































































Reviews:

No comments