Endress+Hauser Hart Proline Promag P 500 Operating Instructions Manual Download Page 186

Page: 186 / 210

Technical data

Proline Promag P 500 HART

186

Hauser

Electrical conductivity

Max. ±5 % o.r.

Influence of ambient

temperature

Current output

Temperature coefficient

Max. 1 μA/°C

Pulse/frequency output

Temperature coefficient

No additional effect. Included in accuracy.

16.7 Installation

"Mounting requirements"

16.8 Environment

Ambient temperature

range

→  26

Temperature tables

Observe the interdependencies between the permitted ambient and fluid

temperatures when operating the device in hazardous areas.
For detailed information on the temperature tables, see the separate document

entitled "Safety Instructions" (XA) for the device.

Storage temperature

–50 to +80 °C (–58 to +176 °F)
• Protect the measuring device against direct sunlight during storage in order to avoid

unacceptably high surface temperatures.

• Select a storage location where moisture cannot collect in the measuring device as

fungus or bacteria infestation can damage the liner.

• If protection caps or protective covers are mounted these should never be removed

before installing the measuring device.

Degree of protection

Transmitter

• As standard: IP66/67, type 4X enclosure

• When housing is open: IP20, type 1 enclosure

• Display module: IP20, type 1 enclosure

Sensor

As standard: IP66/67, type 4X enclosure

External WLAN antenna

IP67

Vibration resistance

• Vibration, sinusoidal according to IEC 60068-2-6

– 2 to 8.4 Hz, 7.5 mm peak

– 8.4 to 2

000 Hz, 2 g peak

• Vibration broad-band random, according to IEC 60068-2-64

– 10 to 200 Hz, 0.01 g

/Hz

– 200 to 2

000 Hz, 0.003 g

/Hz

– Total: 2.70 g rms

Summary of Contents for Hart Proline Promag P 500



















































































































































































































Search results

Summary of Contents for Hart Proline Promag P 500

Reviews:

Endress+Hauser Hart Proline Promag P 500, Operating Instructions Manual, Page: 186 / 210

Search results

Summary of Contents for Hart Proline Promag P 500

Reviews: