manualshive.com logo in svg

Endress+Hauser Hart Proline Promag P 500, Operating Instructions Manual, Page: 14 / 210

Share
Download
Endress+Hauser Hart Proline Promag P 500 Operating Instructions Manual Download Page 14

Product description

Proline Promag P 500 HART

14

Hauser

3  

Product description

The measuring system consists of a transmitter and a sensor. The transmitter and sensor

are mounted in physically separate locations. They are interconnected by one or two

connecting cable(s).

3.1  

Product design

Two versions of the transmitter are available.

3.1.1  

Proline 500 – digital

Signal transmission: digital

Order code for "Integrated ISEM electronics", option 

A

 "Sensor"

For use in applications not required to meet special requirements due to ambient or

operating conditions.
As the electronics are located in the sensor, the device is ideal:

For simple transmitter replacement.
• A standard cable can be used as the connecting cable.

• Not sensitive to external EMC interference.

5

2

-

+

-

ESC

1

4

3

  A0029593

 1

Important components of a measuring device

1

Electronics compartment cover

2

Display module

3

Transmitter housing

4

Sensor connection housing with integrated ISEM electronics: connecting cable connection

5

Sensor

Summary of Contents for Hart Proline Promag P 500



















































































































































































































Reviews:

No comments