Endress+Hauser Fieldgate FXA520 Operating Instructions Manual Download Page 84

Page: 84 / 108

7 Viewing Information (User Mode)

Fieldgate FXA520

Hauser

HART Log

The HART log records messages relating to HART communication, e.g. device detected/removed

etc. Up to 25 lines are displayed. The log is deleted when the Fieldgate is switched off. Table 7-9

explains the significance of the parameters.

Table 7-9: HART log messsages

HART server log

The HART Server log records messages relating to the HART server, e.g Telnet login etc. Up to 25

lines are displayed. The log is deleted when the Fieldgate is switched off. Table 7-10 explains the

significance of the parameters.

Table 7-10: HART log messages

Modem Log

The modem log can be used to check the correct function of the Fieldgate with GSM modem. Up

to 25 lines are displayed. The log is deleted when the Fieldgate is switched off. Table 7-11 explains

the significance of the parameters.

HART log message

Meaning

Device '<device-id>': detected

Device with the HART-ID indicated has been detected

Device '<device-id>': disconnected

Device with the HART-ID indicated has disappeared

HART server log message

Meaning

'<username>' logged in from <ip-addr>

Someone has logged onto the HART server from the

IP address indicated (plain text authentication)

'<username>' logged in with MD5 authorization from

ditto with MD5 authentication

'<username>' logged off from <ip-addr>

Someone has logged off the HART server

'<username>' selected ill protocol '<protocol>' from

Protocol selected is invalid

'<username>' wrong user/password form <ip-addr>

Invalid user/password

Modem log message

Connection

Meaning

dial in (Server)

carrier lost (Server)

hangup requested by command (Server)

hangup (Server)

Modem/GSM

Diagnosis messages for dial-in with Fieldgate

dial in disabled!

Modem/GSM

Fieldgate was called (with maximum number of

rings) but dial-in is not allowed

assigned IP: <ip-addr>

carrier lost

hangup requested by command

hangup

connect failed

hangup requested by SMS transmission

hangup caused by PPP

Modem/GSM

Diagnosis messages for dial-in with ISP

assigned IP: <ip-addr>

GPRS Network: <gprs network>

GPRS-QOS: <QOS> connect failed

GPRS hangup requested by ring or carrier loss

GPRS hangup requested by command

GPRS hangup requested by SMS transmission

GPRS hangup caused by PPP

GPRS hangup

GSM

Diagnosis messages for dial-in with GPRS

initiating call back

Modem/GSM

Call-back to ISP started due to ringing

Summary of Contents for Fieldgate FXA520













































































































Search results

Summary of Contents for Fieldgate FXA520

Reviews:

Brands by name

Popular brands

Endress+Hauser Fieldgate FXA520, Operating Instructions Manual

Search results

Summary of Contents for Fieldgate FXA520

Reviews:

Brands by name

Popular brands