Endress+Hauser Deltabar S PMD70 Operating Instructions Manual Download Page 54 | Manualshive

Page: 54 / 156

background image

Description of parameters

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

54

Hauser

POS. ZERO ADJUST (685)
Entry

Position adjustment – the pressure difference between zero (set point) and the measured
pressure need not be known.

Example:

– MEASURED VALUE = 2.2 mbar (0.033 psi)
– Correct the MEASURED VALUE via the POS. ZERO ADJUST parameter with the

"Confirm" option. This means that you are assigning the value 0.0 to the pressure
present.

– MEASURED VALUE (after pos. zero adjust) = 0.0 mbar
– The current value is also corrected.

The CALIB. OFFSET parameter displays the resulting pressure difference (offset) by which
the MEASURED VALUE was corrected.

Selection:

• Abort
• Confirm

Factory setting:

0.0

POS. INPUT VALUE (563)
Entry

Position adjustment – the pressure difference between zero (set point) and the measured
pressure need not be known. To correct the pressure difference, you need a reference
measurement value (e. g. from a reference device).

Example:

– MEASURED VALUE = 0.5 mbar (0.0075 psi)
– For the POS. INPUT VALUE parameter, specify the desired set point for the

MEASURED VALUE, e.g. 2.0 mbar (0.03 psi).
(MEASURED VALUE

new

= POS. INPUT VALUE)

– MEASURED VALUE (after entry for POS. INPUT VALUE) = 2.0 mbar (0.03 psi)
– The CALIB. OFFSET parameter displays the resulting pressure difference (offset) by

which the MEASURED VALUE was corrected.
CALIB. OFFSET = MEASURED VALUE

old

– POS. INPUT VALUE,

here: CALIB. OFFSET = 0.5 mbar (0.0075 psi) – 2.0 mbar (0.03 psi) = – 1.5 mbar
(0.0225 psi))

– The current value is also corrected.

Factory setting:

0.0

CALIB. OFFSET (319)
Entry

Position adjustment - the pressure difference between zero (set point) and the measured
pressure is known.

Example:

– MEASURED VALUE = 2.2 mbar (0.033 psi)
– Via the CALIB. OFFSET parameter, enter the value by which the MEASURED VALUE

should be corrected. To correct the MEASURED VALUE to 0.0 mbar, you must enter
the value 2.2 here.
(MEASURED VALUE

new

= MEASURED VALUE

old

– CALIB. OFFSET)

– MEASURED VALUE (after entry for calib. offset) = 0.0 mbar
– The current value is also corrected.

Factory setting:

0.0

Table 6: (GROUP SELECTION



)



OPERATING MENU



SETTINGS



POSITION ADJUSTMENT

Parameter name

Description

«
...
52
53
54
55
56
...
»

Summary of Contents for Deltabar S PMD70





























































































































































Reviews:

No comments

Related manuals for Deltabar S PMD70

Brand: Paradyne Pages: 86

Brand: Davis Instruments Pages: 16

Brand: Canon Pages: 16

Brand: Canon Pages: 48

Brand: Canon Pages: 12

Brand: GE Pages: 20

Brand: GE Pages: 2

Brand: Vaisala Pages: 24

E-P2 - PEN 12.3 MP Micro Four Thirds Interchangeable Lens Digital...

Brand: Olympus Pages: 2

AS4000 - AS Transcription Kit

Brand: Olympus Pages: 24

Maintenence Kits

Brand: Generac Power Systems Pages: 1

IMI SENSORS EX640B61

Brand: PCB Piezotronics Pages: 70

Brand: Roav Pages: 10

Brand: SUP’AIR Pages: 29

Care@Home MDsense

Brand: Essence Smartcare Pages: 12

5TH GEN 4RUNNER

Brand: Victory 4x4 Pages: 5

Brand: Keith Pages: 2

Radfire RAS Series

Brand: Puretec Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands