Endress+Hauser Deltabar S PMD70 Operating Instructions Manual Download Page 26

Page: 26 / 156

Level measurement

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Hauser

5.4.2

Calibration without reference pressure – dry calibration

Example:

In this example, the volume in a tank should be measured in m

. The maximum volume is 5 m

and the maximum height 4 m (13 ft). The density of the fluid is 1 kg/dm

. The device is mounted

below the level lower range value.

Prerequisite:

• The measured variable is in direct proportion to the pressure.
• This is a theoretical calibration, i.e. the tank volume, tank height and density of the fluid are

known.

Note!
• See also Operating Instructions for Deltabar S (BA00270P) or Cerabar S (BA00271P), Section 6.5

"Level measurement" or Deltapilot S (BA00332P), Section 6.4 "Level measurement".

• Due to the orientation of the device, there may be a shift in the measured value, i.e. when the

container is empty or partly filled, the MEASURED VALUE parameter does not display zero.



To perform a position adjustment see also Page , Table 6: Position adjustment.

• For a description of the parameters mentioned, see

– Page 45, Table 2: MEASURING MODE
– Page 67, Table 10: BASIC SETUP
– Page 70, Table 11: BASIC SETUP – "Linear" level type.

• For a description of further relevant parameters, see

– Page 96, Table 16: EXTENDED SETUP
– Page 122, Table 26: PROCESS VALUES.

Warning!
If the measuring mode is changed, the span setting (URV) must be verified in the "Calibration"



"Basic Setup" operating menu and, if necessary, reconfigured.

Description

Select the "Level" measuring mode via the MEASURING
MODE parameter.

On-site display:
Menu path: GROUP SELECTION



MEASURING

MODE

Digital communication:
Menu path: OPERATING MENU



SETTINGS



BASIC SETUP



MEASURING MODE

P01-PMP75xxx-19-xx-xx-xx-003

Fig. 13:

Calibration without reference pressure –
dry calibration

See table, step 9.

See table, step 10.

See table, step 11.

See table, step 12.

If necessary, select "Level Standard" level mode using the
LEVEL SELECTION parameter.

On-site display:
Menu path: GROUP SELECTION



MEASURING

MODE "Level"



LEVEL SELECTION

Digital communication:
Menu path: OPERATING MENU



SETTINGS



BASIC SETUP



MEASURING MODE "Level"



LEVEL SELECTION

On-site display:
Select BASIC SETUP function group. Menu path:
GROUP SELECTION



OPERATING MENU



SETTINGS



BASIC SETUP

4 m

–0.5 m

➂

➃

➁

= 1

V = 5 m

➀

Summary of Contents for Deltabar S PMD70





























































































































































Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands

Endress+Hauser Deltabar S PMD70, Operating Instructions Manual

Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands