Endress+Hauser Deltabar S PMD70 Operating Instructions Manual Download Page 17 | Manualshive

Page: 17 / 156

background image

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Level measurement

Hauser

17

5.2.2

Calibration without reference pressure – dry calibration

Example:

In this example, the volume in a tank should be measured in litres.The maximum volume of 1000
litres (264 US gal) corresponds to a pressure of 450 mbar (6.75 psi). The minimum volume of 0
litres corresponds to a pressure of 50 mbar (0.75 psi), as the device is mounted below the level lower
range value. The device is mounted below the level lower range value.

Prerequisite:

• The measured variable is in direct proportion to the pressure.
• This is a theoretical calibration i.e. the pressure and volume values for the lower and upper

calibration point must be known.

!

Note!
• See also Operating Instructions for Deltabar S (BA00270P) or Cerabar S (BA00271P), Section 6.5

"Level measurement" or Deltapilot S (BA00332P), Section 6.4 "Level measurement".

• The values entered for EMPTY CALIB./FULL CALIB. and SET LRV/SET URV must have a

minimum interval of 1% for the "Level Easy Pressure" level mode. The value will be rejected with
a warning message if the values are too close together. Further limit values are not checked; i.e.
the values entered must be appropriate for the sensor and the measuring task so that the
measuring device can measure correctly.

• Due to the orientation of the device, there may be a shift in the measured value, i.e. when the

container is empty or partly filled, the MEASURED VALUE parameter does not display zero.



To perform a position adjustment see also Page 53, Table 6: Position adjustment.

• For a description of the parameters mentioned, see

– Page 45, Table 2: MEASURING MODE
– Page 58, Table 8: LEVEL SELECTION "Level Easy Pressure"

• For a description of further relevant parameters, see

– Page 96, Table 16: EXTENDED SETUP
– Page 122, Table 28: PROCESS VALUES.

#

Warning!
If the measuring mode is changed, the span setting (URV) must be verified in the "Calibration"



"Basic Setup" operating menu and, if necessary, reconfigured.

Description

1

Select the "Level" measuring mode via the MEASURING
MODE parameter.

On-site display:
Menu path: GROUP SELECTION



MEASURING

MODE

Digital communication:
Menu path: OPERATING MENU



SETTINGS



BASIC SETUP



MEASURING MODE

P01-PMC71xxx-19-xx-xx-xx-000

Fig. 5:

Calibration without reference pressure –
dry calibration

1

See Table, Steps 7 and 8.

2

See Table, Steps 9 and 10.

2

If necessary, select "Level Easy Pressure" level mode
using the LEVEL SELECTION parameter.

On-site display:
Menu path: GROUP SELECTION



MEASURING

MODE "Level"



LEVEL SELECTION

Digital communication:
Menu path: OPERATING MENU



SETTINGS



BASIC SETUP



MEASURING MODE "Level"



LEVEL SELECTION

3

On-site display:
Select BASIC SETUP function group. Menu path:
GROUP SELECTION



OPERATING MENU



SETTINGS



BASIC SETUP

1000 l

50 mbar

450 mba

0 l

ρ

= 1

kg

dm

3

1

2

«
...
15
16
17
18
19
...
»

Summary of Contents for Deltabar S PMD70





























































































































































Reviews:

No comments

Related manuals for Deltabar S PMD70

Brand: omnicharge Pages: 12

Brand: omnicharge Pages: 72

Brand: Wallenstein Pages: 31

Brand: Nauticam Pages: 2

Brand: B-TEK Scales Pages: 3

Brand: B-Speech Pages: 18

Brand: B-PWR Pages: 12

Brand: Ecco Pages: 9

Brand: Ecco Pages: 9

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: TAUBENREUTHER Pages: 11

Brand: Yakima Pages: 15

Brand: Biral Pages: 15

Brand: Saxby Pages: 2

Brand: SIIG Pages: 12

Brand: B-Speech Pages: 24

Brand: Doug Thorley Headers Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands