Endress+Hauser Deltabar S PMD70 Operating Instructions Manual Download Page 113

Page: 113 / 156

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Description of parameters

Hauser

113

ALT. CURR. OUTPUT (597)
Selection

Set current output if sensor limits undershot or overshot.

Options:

• Normal: the current output assumes the value set via the OUTPUT FAIL MODE and

SET MAX. ALARM parameters.

• Special:

– Lower sensor limit undershot (E120):

Current output = 3.6 mA

– Upper sensor limit overshot (E115): current output assumes the value set via the

SET MAX. ALARM parameter.

Attention : when using the case "special", the behavior is limited to an over/
underpressure in a range LRL -10%, URL +10%.

Factory setting:

Normal

SET MAX. ALARM (342)
Entry

Enter current value for maximum alarm current.



Summary of Contents for Deltabar S PMD70





























































































































































Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands

Endress+Hauser Deltabar S PMD70, Operating Instructions Manual

Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands