manualshive.com logo in svg

Endress+Hauser ControlCare SFC162, Operating Instructions Manual, Page: 15 / 64

Share
Download
Endress+Hauser ControlCare SFC162 Operating Instructions Manual Download Page 15

ControlCare Field Controller: Commissioning and Configuration

2 Getting Started

Hauser

13

2.6

Checking Your Installation

2.6.1

License

You can check your license to see the number of Tags and Function Blocks that are supported. This 
information is also required should you want to request a Tags license upgrade.

1 Open Check Licence: 

–

Start=>Programs =>Hauser=>ControlCare=>Tools=>Check License

2 In the example, it can be seen that there are two licenses in the hard key (dongle): 

–

Field Control OPC Server supports an unlimited number of tags

–

ControlCare Application Designer supports 256 Function Blocks. 

2.6.2

Application versions

It is sometimes necessary to check all product related version information, for example, when you 
are looking for product support or a product update. 

1 Open About ControlCare: 

–

Start=>Programs =>Hauser=>ControlCare=>Tools=>About ControlCare

2 A dialog box now appears containing all version information for ControlCare software 

components.

–

It can be copied onto the clipboard by selecting the text within the box by scrolling the 
mouse over it. 

–

Now press the sequence "

Crtl+Insert

" to copy it and "

Shift+Insert

" to paste it into another 

text document.

Summary of Contents for ControlCare SFC162

































































Reviews:

No comments