Endress+Hauser Analytik Jena Multi X 2500 Operating Manual Download Page 27

Page: 27 / 124

multi X 2500

Function and layout of the multi X 2500

Fig. 16 Auto-protection assembly

1  Hose 11 (compressed argon gas for pneumatic seal)
2  Hose 8 (argon for safety purging)
3  Heated gas transfer line to the chlorine module

4 Knob of the clamping mount
5 Valve assembly with integrated filter and

pneumatic seal

6 Cable for electrical connection

The coupling connects the combustion tube and the measuring gas transfer line. The
combustion tube is inserted into the auto-protection assembly and sealed with a

pneumatic seal. The pneumatic seal is operated with argon. The pneumatic seal is

opened or closed with a toggle switch.



Toggle switch down: Combustion tube sealed



Toggle switch up:

Combustion tube released (e.g. for dismantling)

Fig. 17 Toggle switch to lock/release combustion tube

Coupling with pneumatic
seal

Summary of Contents for Analytik Jena Multi X 2500





























































































































Search results

Summary of Contents for Analytik Jena Multi X 2500

Reviews:

Related manuals for Analytik Jena Multi X 2500

Brands by name

Popular brands

Endress+Hauser Analytik Jena Multi X 2500, Operating Manual

Search results

Summary of Contents for Analytik Jena Multi X 2500

Reviews:

Related manuals for Analytik Jena Multi X 2500

Brands by name

Popular brands