ENDA ATC9311
ANALOG THERMOSTAT with DIGITAL DISPLAY
ATC9311-E-05-R
Plastic injection presses, automatic bread making ovens, nylon bag machines,
shrink packing machines, furniture presses, industrial ovens, textile machines,
ironing presses and other temperature control applications.
Application areas
* 96 x 96mm sized.
* Digital display for measured temperature and set value.
* Selectable On-Off or time proportional control.
* Fe-Const thermocouple input.
* Output relay is de-energized in the case of sensor failure.
* Easy setting procedure.
* CE marked according to European Norms.
Dimensions
Flush
mounting
adaptor
Rubber
packing
Panel
Panel cut-out
Note:
1/2
Panel thickness
should be
max. 10mm.
105mm
9
9
m
m
90.5mm
9
0
.5
m
m
Read this document carefully before using this device. The guarantee will be
expired by damaging of the device if you don't attend to the directions in the user
manual. Also we don't accept any compensations for personal injury, material
damage or capital disadvantages.
Thank you for choosing ENDA ATC9311 temperature controller.
,
For removing mounting clamps: Push out the flush-mounting clamp in
direction
1
as
shown in the figure above. Then, pull out the clamp in
direction
2.
If there is no 60mm free space at back side of the device, it would be difficult to remove it from
the panel.
200
250
400
300
350
100
150
50
0
°C
ENDA
ATC9311
OUT
SET
Temperature setting
knob
Control output state LED
(Light is on when control output is energized)
Set key
Temperature display
9
6
m
m
99mm
1
OUT
200
250
150
°C
300
100
350
50
400
0
ENDA
ATC9311
SET
Technical Specifications
Supply
230V AC +10% -20%, 50/60Hz or 24V AC 10%, 50/60Hz or optional
9-30V DC / 7-24V AC 10% SMPS module.
±
±
Power consumption
Max. 5VA
2.5mm² screw-terminal connection.
Wiring
HOUSING
Housing type
Suitable for flush-panel mounting.
Dimensions
W96xH96xD50mm
Weight
Approx. 250g (after packing)
Enclosure material
Self extinguishing plastics
CONTROL
Control type
Single-setpoint control
On-Off / time proportional (optional)
Control algorithm
A/D converter
9 bits
Proportional band
Control period
Hysteresis
2% (for time proportional control)
10 second (for time proportional control)
4°C (for On-Off control)
OUTPUT
Control output
Relay : 250V AC, 2A (for resistive load), NO+NC or 12V DC 20mA logic output
Mechanical 30.000.000 operation; electrical 300.000 operation
Life expectancy for relay
0 ... 400°C
1°C
For adjustment 4%, for display 0,5% (of full scale) or 1 digit.
±
±
±
3 digits, 7.6mm, 7 segment red LED
Scale
Sensitivity
Accuracy
Display
Data retention
EMC
Safety requirements
EN 61326-1: 1997, A1: 1998, A2: 2001 ( For EMC tests performance criterion B is satisfied.)
EEPROM (at least 10 years)
EN 61010-1: 2001 (Pollution degree 2, overvoltage category II)
ENVIRONMENTAL CONDITIONS
Height
Max. 2000m
80 up to 31°C decreasing linearly 50 at 40°C.
%
%
Ambient/storage temperature
Max. relative humidity
0 ... +50°C/-25... +70°C
Rated pollution degree
According to EN 60529 Front panel : IP60
Rear panel : IP20
Do not use the device in locations subject to corrosive and flammable gases.
While cleaning the device, solvents (thinner, benzine, acid etc.) or
corrosive materials
must not be used.
ELECTRICAL CHARACTERISTICS
Depth
50mm
14mm
57mm
2