background image

EMPYRE PRO SERIES INSTALLATION AND OPERATION MANUAL • 2009 

3

INTRODUCTION

The Empyre Pro Series Hot Water Furnace

You have selected one of the best wood stoves/furnaces on the 

market  today!  It  has  been  specially  designed  to  produce  highly 

efficient heat with emissions well below environmental standards, 

and we are proud to offer a 10 year limited warranty!

To  ensure  maximum  benefit  from  your  new  Empyre  Pro  Series 

furnace,  read  the  Installation  and  Operation  Instruction  Manual 

cover to cover and follow all instructions carefully.

The  Empyre  Pro  Series  furnace  has  been  designed  for  outdoor 

installation and has  also been tested to meet UL  Standard 391 

-  2006/726-06  Standard  C22.2  No.3  and  CSA  B366-1-M91  for 

indoor central solid fuel fired furnaces, therefore it may be installed 

indoors. It is ideally suited for both domestic and commercial use.

Please keep this manual for future reference.

MODEL Empyre Pro Series 200

How The Empyre Pro Series Works

The  Empyre  Pro  Series  uses  a  process  called  wood 

gasification  to  produce  highly  efficient  combustion  in  the 

furnace’s dual burn chambers. (1) Wood in the firebox burns 

from the bottom up, drying the top layer of wood in the firebox 

and forcing gases and exhaust into the lower burn chamber. 

(2)  In  the  brick-lined  lower  chamber,  these  volatile  gases 

are burned at temperatures as high as 2000°F (1093°C).* 

The firebrick lining in both burn chambers absorbs the heat 

and  maintains  burn  chamber  temperatures  for  consistent 

gas  combustion.  This  high-temperature  gas  combustion 

significantly  lowers  emissions,  prevents  creosote  buildup, 

and  minimizes  ash  buildup  in  the  unit.  (3)  After  passing 

through  the  burn  chamber,  exhaust  air  escapes  through 

multiple  flues  running  through  the  water  jacket,  heating 

the water quickly and efficiently. (4) The exhaust cools as it 

passes through the flues, and when it leaves the chimney, 

temperatures have fallen to 350°F (177°C).*

*varies based on fuel type, burn rate and other conditions

Read more on gasification on page 19.

1

3

2

4

Summary of Contents for Pro Series 100































Reviews: