background image

INSTALLATION INSTRUCTIONS

AND

OWNER'S MANUAL

UNVENTED 

GAS FIREPLACE

MODELS

VFD26FM(2,3)0(N,W,C)(N,P)-2

VFD26FP(2,3)0L(N,P)-2

VFD26FP70L(N,P)-1

VFD26FP30L10(N,P)-3

VFD26FP70L10(N,P)-1

Vent-Free Gas Fireplaces

This appliance may be installed in an aftermarket, 

permanently located, manufactured (mobile) home, 

where not prohibited by local codes.
This appliance is only for use with the type of gas in-

dicated on the rating plate. This appliance is not con-

vertible for use with other gases.

 

WARNING

If the information in these instructions are not fol-

lowed exactly, a fire or explosion may result caus

-

ing property damage, personal injury or loss of life.

—  Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any 

other appliance.

—  WHAT TO DO IF YOU SMELL GAS

 

•  Do not try to light any appliance.

 

•  Do not touch any electrical switch; do not use 

any phone in your building.

  •  Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas supplier’s 

instructions.

 

•  If you cannot reach your gas supplier, call the 

fire department.

—  Installation and service must be performed by a 

qualified installer, service agency or the gas sup

-

plier.

Installer: 

Leave this manual with the appliance.

Consumer:  Retain this manual for future reference.

This is an unvented gas-fired heater. It uses air (oxy

-

gen) from the room in which it is installed. Provisions 

for adequate combustion and ventilation air must be 

provided. Refer to pages 9 and 10.

WATER VAPOR: A BY-PRODUCT OF UNVENTED 

ROOM HEATERS

Water vapor is a by-product of gas combustion. An 

unvented room heater produces approximately one  

ounce (30ml) of water for every 1,000 BTU's (.3KW's) 

of gas input per hour. Refer to page 8.

 

WARNING

If not installed, operated and maintained in accor-

dance with the manufacturer's instructions, this 

product could expose you to substances in fuel or 

from fuel combustion which can cause death or seri-

ous illness.

Page 1

Summary of Contents for VFD26 Series













































Reviews: