Empire Comfort Systems DVCD32FP30N-1 Owner'S Manual Download

Page: 1 / 60

Page 1

INSTALLATION INSTRUCTIONS

AND

OWNER’S MANUAL

Direct Vent Zero Clearance Gas

Fireplace Heater

GAS-FIRED

EMPIRE

Comfort Systems

DIRECT VENT

GAS FIREpLACE HEATER

MODEL SERIES

MILLIVOLT

DVCD32Fp30(N,p)-1

DVCD36Fp30(N,p)-1

DVCD42Fp30(N,p)-1

DIRECT IGNITION

DVCD32Fp50N-1

DVCD36Fp50N-1

DVCD42Fp50N-1

UL FILE NO. MH30033

Installer:

Leave this manual with the appliance.

Consumer: Retain this manual for future reference.

WARNING: If the information in these instructions

are not followed exactly, a fire or explosion may re

sult causing property damage, personal injury or

loss of life.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

fire department.

— Installation and service must be performed by a

qualified installer, service agency or the gas sup

plier.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA only)

or mobile home, where not prohibited by state or local

codes.
This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certified

kit is used.

WARNING: If not installed, operated and maintained

in accordance with the manufacturer’s instructions,

this product could expose you to substances in fuel

or from fuel combustion which can cause death or

serious illness.

WARNING

HOT GLASS

DO NOT TOUCH

NEVER

WILL

CAUSE BURNS.

GLASS

UNTIL COOLED.

ALLOW CHILDREN

TO TOUCH GLASS.

Summary of Contents for DVCD32FP30N-1





























































Search results

Summary of Contents for DVCD32FP30N-1

Reviews:

Related manuals for DVCD32FP30N-1

Brands by name

Popular brands

Empire Comfort Systems DVCD32FP30N-1, Owner'S Manual

Search results

Summary of Contents for DVCD32FP30N-1

Reviews:

Related manuals for DVCD32FP30N-1

Brands by name

Popular brands