Emil Lux 106715, Original Instructions Manual, Page: 18 / 28

GB
18
– Fix the “Inner fixtures” of the appliance into the
“outer fixtures” of the wall, adjust the right dis-
tance between the appliance and the wall, then fix
them with the M5×14 screws.
– Cover the 4 caps on the “Front fixtures”.
Operation
Check before switching on!
Check the safe condition of the device:
– Check whether there are any visible defects.
– Check whether all parts of the device are firmly
attached.
Use of the item
– Place the heater on flat stable surface
– If the appliance is not used for a long time –
switch it off with power switch and plug the item
out
– Attention! Do not cover the product! Convector
should not be place under shower or in swimming
pool
Touch Control Operation
Operation for Touch Control
– Insert the plug in a suitable power socket.
LCD display
►
Operation – p. 9
1. Time period
2. Monday-Sunday
3. Temperature display
4. Constant temperature heating mode
5. Heating mode
6. Towel drying mode
7. Timer mode
8. Time display
Operating environment
• Temperature: 5°C…40°C
• Relative humidity:
≤
95%
Power
– Press [ ] button, the screen will be lit up and the
electric towel rack is on standby.
Setting the date and time
– Press [S] button, then press the [+] or [
−
] to set
the hour.
– Press [S] button again, then press the [+] or [
−
] to
set the minute.
– Press [S] button again, then press the [+] or [
−
] to
select the date.
– Press [S] button to complete.
Mode switch
– Press [M] button to set the constant temperature
heating mode, heating mode, towel drying mode,
timer mode.
Constant temperature heating mode:
– The default set temperature is 35 °C, press [+]
or [
−
] to set the temperature, which ranges from 5
to 40 °C.
Once the defined temperature is reached, it will auto-
matically stand by and it will automatically operate
again when the temperature decreases.
Heating mode:
The towel hanging rod will operate at the highest tem-
perature in this mode.
– The default set temperature is 40 °C, press [+]
or [
−
] to set the temperature, which ranges from 5
to 40 °C.
Towel drying mode:
The heater will operate 4 hours and automatically
turn off in this mode.
The mode is specially set for drying towel or bath
towel, when it stop heating, take down the warm and
fluffy towel.
It generally takes about one hour to dry the towel and
2 hours to restore fluffy feel and 4 hours to dry the
bath towel.
Timer mode:
User can set on/off time and temperature, it only need
to set one automatic cycle each week, it can be set as
(Monday to Sunday, 4 time periods can be set per
day) for energy saving and ease the burden to our
beautiful Earth.
Time setup steps for timer setting
– Press [M] button to timer mode.
– Keep press [S] button until you reach the date
you want.
– Press [S] button, the [ON] icon flashes, it means
to set the [ON] timer.
– Press [M] button, press the [+] or [
−
] to adjust the
hour (00-23h).
– Press [M] button again, press the [+] or [
−
] to
adjust the minute (00-59s).
– Press [M] button again, press the [+] or [
−
] to set
the temperature (5-40°C).
– Press [S] button, the [OFF] icon flashes, it means
to set the [OFF] timer.
– Press [M] button, press the [+] or [
−
] to adjust the
hour (00-23h).
– Press [M] button again, press the [+] or [
−
] to
adjust the minute (00-59s).
DANGER! Risk of injury! The device must
only be put into operation if no faults are
found during the check-up. If any part of the
device is defective, it must be replaced
before the next use.
DANGER! Risk of injury! The device may
not be mounted directly below a wall outlet.
Danger of cable fires!
When start the system, the default mode is
the mode before last shutdown.
Don’t remember timer when power is off.
Please do NOT hang any objects to be dried
on the heater for a long time, otherwise, it
may cause damage of other objects or color
fading of the towel or even stick the towel on
the heater.
After the product is powered off, the timer
settings are not retained.