background image

www.enviromaster.com

WLCA/WLHA High Wall Evaporator

26

Note:

  While  in  Remote  thermostat 

mode  (see  configuration),  only  the 

“FAN”  and  “TIME”  buttons  are  acti

-

vated and will beep when pressed.

Memory Backup:

In the event of a power failure the control will 

retain all of it’s settings including the mode 

of operation. When power is restored, after 

a three minute time delay, the control will re

-

turn to the mode of operation that it was in 

prior to the power failure.

fault Conditions

Room air sensor fault: E01

If  the  room  air  sensor  is  disconnected, 

damaged or malfunctions the LCD display 

will flash error code “E01” to signify that 

a fault has occurred. Operation will con

-

tinue with the control using the last known 

value for the room air sensor.

 sEqUEnCE of opErAtion – WALL moUntEd tHErmostAt modE

Condensate fault: E02

If  the  control  senses  a  condensate  fault 

condition either through the optional con

-

densate pumps safety switch or the drain 

pan  sensors,  the  LCD  display  will  flash 

error  code  “E02”.  The  compressor  will 

switch off for a minimum of three minutes 

and until the fault condition is corrected.

ID coil sensor fault: E03 

The indoor coil sensor monitors the tem-

perature  of  the  indoor  coil.  If  a  freeze 

condition  exists  continuously  for  three 

minutes, the LCD will display error code 

“E03” to signify that a fault has occurred. 

The compressor will switch off for a mini

-

mum of three minutes and until the fault 

condition is corrected. Also, if the micro

-

processor  detects  an  evaporator  freeze 

condition four times within a 24 hour pe

-

riod, the filter check indicator will appear.

 

infrArEd rEmotE ControL option

operational range 55- 90° f (in 1° increments.)

NOTE: Batteries Included.

Pressing    the  “+”  will  increase 

the set point temperature setting. 

Pressing  the  “-“  button  will  de

-

crease  the  setpoint  temperature 

setting.

poWEr

 

 

Pressing the

 “poWEr” 

button will 

turn the unit On or Off.

fAn

 

 

Pressing  the 

“fAn”

  button  will 

place the unit in fan mode.

AUto

 

Pressing  the 

“AUto”

  button  will 

place the unit in Auto changeover 

mode.

fAn spEEd

 

Pressing  the 

“fAn  spEEd” 

but-

ton will scroll the unit through fan 

the  fan  speed  selection.  The  se

-

quence is High, Low and Auto.

HEAt

 

Pressing the 

“HEAt”

  button  will 

place the unit in Heat mode.

CooL

 

Pressing the 

“COOL”

 button will 

place the unit in Cool mode.

dry

 

Pressing the “DRY” button will 

place the unit in Dry Mode.

LoUVEr

Pressing  the  “LOUVER”  button 

will  enter  the  Louver  Configura

-

tion  mode.  While  in  Louver  Con-

figuration  mode,  each  successive 

press of the louver button will scroll 

through the louver positions. After 

idle  for  10  seconds,  the  control 

will  exit  the  Louver  Configuration 

mode.

Figure 6

Summary of Contents for AmericaSeries WLC30









































Reviews: