manualshive.com logo in svg

Emerson unidrive m, Installation And Operating Manual, Page: 48 / 88

Share
Download
Emerson unidrive m Installation And Operating Manual Download Page 48

48

 SI-Safety Installation & Operating Manual 

Issue Number: 1

6

Start-up

6.1

Procedure

Start-up / commissioning must only be performed by suitably trained and skilled 
personnel. Observe all safety instructions during start-up / commissioning.

6.1.1

LED display

Following a reboot, the following sequences run whenever a session is completed 
without faults being reported. The result is displayed on the front panel LED display.

Table 6-1 Key to LED display

6.2

Configuration

Configuration is performed using the '

CTSafePro

' program. To be able to transmit data 

to the module, a programming adapter is required, and its drivers need to be installed 
before it is used for the first time.

CTSafePro

 is a graphical PC tool which enables the configuration of the speed encoder 

interface, definition of the safe motion functionality and logic operations. It also provides 
testing and advanced diagnostic tools.
The configuration is saved and protected against line power failure within the module.
Refer to 

CTSafePro help

 for details of how to configure the SI-Safety module. 

6.2.1

Downloading the configuration to the SI-Safety module

The configuration is downloaded to the SI-Safety module via a serial cable connected 
between the PC and the SI-Safety module RJ45 port. Refer to 

CTSafePro help

 for 

details of downloading the configuration.

Mode

Description

LED display

Start-up

Synchronization between the 
two processor systems and 
checking of the configuration 
and firmware data

Off

RUN

Normal operation of the system. 
All outputs are switched to 
reflect the prevailing status of 
the logic unit.

Flashing green (1 Hz)

STOP

In Stop mode, parameter and 
program data can be loaded 
externally. 

Flashing red/green (1 Hz)

ALARM

Alarm can be reset by digital 
input.

Flashing red /yellow (1 Hz)

Fault

Fault can only be reset by 
power cycling.

Continuous red

Not validated

System running but not 
validated

Flashing yellow (1 Hz)

An isolated serial communications cable must be used to connect the SI-Safety module 
to IT equipment (i.e. laptop computers). Suitable cables are available from Control 
Techniques.

WARNING

Summary of Contents for unidrive m

























































































Reviews:

No comments