background image

4

TESCOM™ 44-6800 E Series

Content

October 2020

Installation, Operations and Maintenance Manual

TR000058ENUS-02_10-20

1

Symbols

 WARNING

Paragraphs highlighted by the WARNING icon contain information about practices or 
circumstances that can lead to personal injury or death, property damage or economic 
loss

.

 CAUTION

Paragraphs highlighted by the CAUTION icon contain information that must be followed 
to maintain a safe and successful operating environment

.

Safety Precautions and Repair

44-6800E Series Regulator Safety

WARNING

Do not attempt to select, install, use or maintain this regulator until you have read and 
fully and understood these instructions. Do not permit untrained persons to install, use 
or maintain this regulator.

The 44-6800E Series regulator should not be installed in an enclosure that is heated above 
the regulator’s maximum rated ambient temperature.

Be sure this information reaches the operator and stays with the product after installation.

Improper selection, improper installation, improper maintenance, misuse or abuse of 
regulator can cause death, serious injury and property damage.

Possible consequences include but are not limited to:

 

High velocity fluid (gas or liquid) discharge

 

Parts ejected at high speed

 

Contact with fluids that may be hot, cold, toxic or otherwise injurious

  

 

 

Explosion or burning of the fluid

 

Lines/hoses whipping dangerously

 

Damage or destruction to other components or equipment in the system

2

2.1

Summary of Contents for TESCOM 44-6800 E Series





















Reviews: