manualshive.com logo in svg

Emerson RXi2-BP, Hardware Reference Manual

Share
Download
Emerson RXi2-BP Hardware Reference Manual Download Page 37

RXi2-BP Hardware Reference Manual 

Section 8 

GFK-3187B 

November 2020 

 

Thermal Performance 

32 

8.1.3

 

Temperature Monitoring and Protection 

The RXi2-BP can monitor critical temperatures on-module and on-carrier and is configured to protect 
itself from an overtemperature condition. 
IPC peripheral circuitry provides two static thermal zones (TZE1 and TZE2) and the CPU circuitry 
provides also two thermal zones (TZCP and TZD1). 
The current thermal state can be always checked with the THRM LED? state.  
If an overtemperature situation is present and the system shuts off, the last LED state is visible also in 
S4/S5. 

The following activities are implemented when conducted in an ACPI aware Operating System. Any 
non-ACPI aware operating system must rely on internal hardware protection and must be evaluated 
separately on a case-by-case basis. 

Once the T

HOT

 threshold is exceeded, the system will try to shutdown graceful into S4, depending on OS  

configuration. 

Figure 26: Thermal Zones: Tactive to Thot 

Temp

SMB-Alert

LED Red

Thot

OS 

SMBus

Exp

TZ: Active

Tactive

 

Note: Thermal Zone 

‘

Active

’

 is optional and not implemented in fanless RXi2-BP design. 

 

 

 

Summary of Contents for RXi2-BP














































Reviews:

No comments

Brands by name

Popular brands

Load more brands