manualshive.com logo in svg

Emerson RXi2-BP, Hardware Reference Manual

Share
Download
Emerson RXi2-BP Hardware Reference Manual Download Page 31

RXi2-BP Hardware Reference Manual 

Section 6 

GFK-3187B 

November 2020 

 

Troubleshooting   

26 

6.1.8

 

µSD Slot 

The RXi2-BP provides a µSD card slot with a mechanical lock. 

Figure 25:  µSD Slot 

 

Signal Name  

Pin 

DATA2 

1 

DATA3 

2 

CMD 

3 

VDD 

4 

CLK 

5 

VSS 

6 

DATA0 

7 

DATA1 

8 

CD 

9 

 

6.2

 

Internal Interfaces 

6.2.1

 

M.2 (SATA) 

A mass storage M.2 type M-connector (per Spec 3.0 V1.2; June 2019) is located under the system lid 
and can only accommodate devices with the SATA interface; no NVMe modules are supported. 
Form factors 2042, 2060, and 2080 are supported and 2042 is the default. 
If you require to change from form factor 2042 to any other please contact Emerson support for 
guidance. 

The pinout is specified in the M.2 standard and is not listed in this document. 

6.3

 

Internal Devices 

6.3.1

 

MRAM

 

The RXi2-BP is capable of Non-Volatile Random Access Memory (MRAM) with 1 Mbit.  

MRAM is an optional feature. Contact Emerson for assistance. 

 

 

Summary of Contents for RXi2-BP














































Reviews:

No comments

Brands by name

Popular brands

Load more brands