Emerson Rosemount Smart Wireless THUM Reference Manual Download Page 46 | Manualshive

Page: 46 / 60

background image

Reference Manual

00809-0100-4075, Rev BA

October 2010

Smart Wireless THUM Adapter

A-2

Weight

THUM Adapter only AL - 0.65 lbs. (0.29 kg)

THUM Adapter only SST - 1.1 lbs. (0.5 kg)

AL THUM Adapter with AL remote kit - 3.2 lbs. (1.45 kg)

SST THUM Adapter with SST remote kit - 5.8 lbs. (2.65 kg)

AL THUM Adapter with M20 conduit adapter - 0.85 lbs. (.038 kg)

SST THUM Adapter with M20 conduit adapter - 1.3 lbs. (0.59 kg)

Enclosure Ratings

Housing option code D is NEMA 4X, and IP66.

Mounting

The THUM Adapter may be attached directly to the conduit of any 2- or 4-wire
HART device or mounted remotely by using the remote mount kit.

PERFORMANCE
SPECIFICATIONS

ElectroMagnetic Compatibility (EMC)

All Models:

Meets all relevant requirements of EN 61326-1 (2006) when installed with
shielded wiring. The sub-device must also use shielded wiring for installation.

Vibration Effect

Output unaffected when tested per the requirements of IEC60770-1 field with
general application or pipeline with low vibration level (10-60 Hz 0.15 mm
displacement peak amplitude / 60-500 Hz 2g).

When the THUM Adapter is used on wired devices that are subject to
vibration levels greater than 2g, it is recommended that the THUM Adapter be
remotely mounted using the remote mount kit.

Temperature Limits

Output Specifications

The THUM allows Wireless communication between the HART device it is
connected to and the Smart Wireless Gateway.

Operating Limit

Storage Limit

–40 to 185 °F
–40 to 85 °C

–40 to 185 °F
–40 to 85 °C

«
...
44
45
46
47
48
...
»

Summary of Contents for Rosemount Smart Wireless THUM





























































Reviews:

No comments

Related manuals for Rosemount Smart Wireless THUM

AirPlus G DWL-G510

Brand: D-Link Pages: 12

Brand: Pace Pages: 15

Component Video Adapter

Brand: ATI Technologies Pages: 16

Brand: Emulex Pages: 19

Brand: ResMed Pages: 31

Brand: 7inova Pages: 36

Brand: Fujitsu Pages: 4

Brand: Fujitsu Pages: 14

Brand: Fujitsu Pages: 23

Brand: Fujitsu Pages: 2

Brand: Fujitsu Pages: 23

EMA-MB91F467S-LS-176M07

Brand: Fujitsu Pages: 26

Brand: Fujitsu Pages: 30

F2MC FAMILY MB2142-03

Brand: Fujitsu Pages: 31

Brand: Fujitsu Pages: 118

Brand: Fujitsu Pages: 1

Brand: Fujitsu Pages: 4

FriendlyNET Wireless USB Adapter

Brand: Asante Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands