Emerson Rosemount CT5100 Reference Manual Download Page 165

Page: 165 / 179

ATEX/IECEX assessment report

summary

14.1

Certification overview

This article is in accordance with IEC 60079-0: 2011 Clause 30. This article must not be

changed amended or removed.

This report covers the assessment of the Rosemount

™

CT5100(Ex) Continuous Gas

Analyzer to the standards listed in

Assessment standards

, in order to support the issue of

prime ATEX and IECEx certification.

14.2

Applicant's name and address

Cascade

™

Technologies Ltd.

Glendevon House

Castle Business Park

Stirling

FK9 4TZ

14.3

Manufacturer's name and address

As applicant.

14.4

Trademark

14.5

Product name/model number

Rosemount CT5100(Ex) Continuous Gas Analyzer

14.6

Rating

110 V to 120 V, 60 Hz

220 V to 240 V, 50 Hz

1100 W

Reference Manual

ATEX/IECEX assessment report summary

00809-0100-4512

October 2019

Reference Manual

165

Summary of Contents for Rosemount CT5100




















































































































































































Search results

Summary of Contents for Rosemount CT5100

Reviews:

Related manuals for Rosemount CT5100

Brands by name

Popular brands

Emerson Rosemount CT5100, Reference Manual

Search results

Summary of Contents for Rosemount CT5100

Reviews:

Related manuals for Rosemount CT5100

Brands by name

Popular brands