manualshive.com logo in svg

Emerson ROSEMOUNT Analytical SPS 4000 B201110, Instruction Manual

Share
Download
Emerson ROSEMOUNT Analytical SPS 4000 B201110 Instruction Manual Download Page 18

Instruction Manual

IB-106-340AC    Rev. 1.3
January 2003

2-2     Installation

Rosemount Analytical Inc.    A Division of Emerson Process Management

SPS 4000

1/4 IN. TUBE FITTING FOR

LOW CALIBRATION GAS IN

1/4 IN. TUBE TO CALIBRATION

GAS FLOWMETER

1/4 IN. TUBE FITTING

FOR HIGH CALIBRATION

GAS IN

0.94 (23.88)

0.94 (23.88)

2.00

(50.80)

1/2 IN. NPT CONDUIT PORTS

(SEE NOTE 2)

6.12 (155.45)

NOMINAL

2.00 (50.80)

NOMINAL

CLEARANCE

TO REMOVE

COVER

1/4 IN. TUBE FITTING

FOR INSTRUMENT

AIR IN (OPTIONAL)

1/2 IN. CONDUIT

FITTING FOR LINE

VOLTAGE

1/2 IN. NPT

CONDUIT PORT

(SEE NOTE 2)

14.81

(376.17)

NOMINAL

CALIBRATION GAS FLOWMETER

(CALIBRATION GAS OUT

TO OXYMITTER 4000)

REFERENCE AIR

FLOWMETER (OPTIONAL)

(REFERENCE AIR OUT

TO OXYMITTER 4000)

13.50

(342.90)

4.25

(107.95)

NOTES: 1.

2.

DIMENSIONS ARE IN INCHES WITH

MILLIMETERS IN PARENTHESES.
THREE 1/2 IN. NPT PORTS ARE PROVIDED

FOR LOGIC I/O AND SIGNAL CONNECTIONS.

THE CABLE ROUTING WILL BE DETERMINED

BY THE CUSTOMER.

9.00 (228.60)

NOMINAL

26010006

Figure 2-1.  Installation

Summary of Contents for ROSEMOUNT Analytical SPS 4000 B201110











































Reviews:

No comments

Brands by name

Popular brands

Load more brands