manualshive.com logo in svg

Emerson Rosemount 8800D Series, Reference Manual, Page: 102 / 192

Share
Download
Emerson Rosemount 8800D Series Reference Manual Download Page 102

92

Reference Manual

00809-0100-4772, Rev FA

Troubleshooting

March 2016

Troubleshooting

7.5.2

Replacing the F

OUNDATION

 Fieldbus electronics boards 

The flowmeter electronics boards may need to be replaced if they have been damaged or 
otherwise become dysfunctional. Use the following procedures to replace electronics 
boards in the flowmeter. You will need a small Phillips-head screwdriver and a pliers.

Note

The electronics boards are electrostatically sensitive. Be sure to observe handling 
precautions for static-sensitive components.

Remove the electronics boards

1.

Turn off the electric power to the flowmeter.

2.

Unscrew and remove the electronics board compartment cover. If the transmitter 
has the LCD display option, the cover will have a glass window.

Figure 7-7. Electronics Board Assembly

A. Transmitter housing
B. Electronics boards
C. LCD display
D. Electronics board compartment cover

3.

If the meter has the LCD display option, loosen the two retaining screws. Remove 
the LCD display and the 10-pin header connector from the electronics board.

4.

Loosen the three captive screws that anchor the electronics.

5.

Use a pliers or a small flathead screwdriver to carefully remove the sensor cable clip 
from the electronics.

6.

Remove thermocouple if the MTA option is installed (requires a 2.5 mm hex 
wrench).

7.

Use the handle molded into the black plastic cover of the electronics boards to 
slowly pull the boards out of the housing.

See 

“Safety messages” on page 81

 for complete warning 

B

A

C

D

Aotewell Ltd 

www.aotewell.com 

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for Rosemount 8800D Series

































































































































































































Reviews:

No comments