Emerson Rosemount 5900S Series Reference Manual Download | Manualshive

Page: 116 / 298

background image

4.6

LPG configuration

4.6.1

Preparations

Prerequisites

Before starting configuration of the Rosemount

™

5900S for LPG measurements, ensure

that all mechanical installations are made according to instructions, and all external
sensors such as pressure and temperature sensors are properly connected.

For Rosemount 5900S with F

OUNDATION

™

Fieldbus the LPG Setup is described in

using DeltaV / AMS Device Manager

Highly pressurized vapor above the product surface affects the propagation speed of
microwaves. The Rosemount 5900S level gauge is able to compensate for this, thus
avoiding deviations in measured level due to the vapor.

When the gauge is installed on the empty tank, calibrate the gauge and configure for LPG
measurements.

To install a Rosemount 5900S for LPG measurements perform the following major steps:

Procedure

1. Install the tank and the Rosemount 5900S level gauge in Rosemount TankMaster

WinSetup as described in the Rosemount Tank Gauging

System Configuration

. Ensure that the appropriate tank and device types are selected, and the

temperature and pressure sensors are properly configured. Check that the gauge
communicates with the TankMaster PC.

2. Install the Rosemount 5900S gauge on the still-pipe. Measure the exact distance to

the Verification Pin.

3. Configure the Rosemount 5900S according to the standard procedure for a

Rosemount 5900S level gauge (see the Rosemount Tank Gauging

Configuration Manual

). Rosemount TankMaster Winsetup is the recommended

configuration tool.

4. Configure the vapor pressure sensor.
5. Set Correction Method to Air Correction Only.
6. Calibrate the Rosemount 5900S.
7. Configure the Verification Pin.
8. Verify position of Verification Pin.
9. Set up the Correction Method that applies to the particular type of product in the

tank.

The LPG installation procedure using Rosemount TankMaster Winsetup is described
in section

LPG setup using Rosemount

.

Configuration

Reference Manual

September 2019

00809-0100-5900

116

Reference Manual

«
...
114
115
116
117
118
...
»

Summary of Contents for Rosemount 5900S Series











































































































































































































































































































Reviews:

No comments

Related manuals for Rosemount 5900S Series

Brand: Naval Pages: 2

Brand: KVH Industries Pages: 51

Super Beam CSB790A

Brand: Comet Pages: 2

AIRNET 11Mb CPE BRIDGE

Brand: Netkrom Pages: 34

SW3-875 LGMQM4 Series

Brand: Panorama Antennas Pages: 3

Brand: LAPLACE INSTRUMENTS Pages: 11

Beagle PRO5B2L2WG-G

Brand: Parsec Technologies Pages: 7

Brand: Patriot Pages: 16

14-Inch DBS Compatible TV Antenna with 24-Inch...

Brand: Radio Shack Pages: 4

iNetVu 1.0 Flyaway

Brand: C-Com Pages: 38

Brand: Jegs Pages: 4

9711-44 KU-BAND TX/RX

Brand: Sea Tel Pages: 256

Campingman GPS/Twin

Brand: Megasat Pages: 15

Brand: Megasat Pages: 23

Brand: BAS Pages: 3

Brand: FreeTec Pages: 2

Brand: gigaAnt Pages: 5

Brand: Xtreme Signal Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands