Emerson Rosemount 3812 Maintenance And Troubleshooting Manual Download Page 93 | Manualshive

Page: 93 / 132

background image

Figure 3-57: CPU or Optional I/O Module replacement

A. Terminal end of Transmitter Electronics Enclosure

B. CPU Module

C. Optional I/O Module

D. Power Supply board

E. Fuse

F. Internal chassis ground

5. Grasp the module you want to replace and pull it out of the enclosure.
6. Insert the new CPU Module or I/O Module into the enclosure and firmly push until

the board is fully seated into the Backplane Board connectors.

7. Replace the terminal blocks for the CPU Module and/or the Optional I/O Module

and tighten the flat head screws with a 3mm flat blade screw driver.

8. Connect to the meter with MeterLink. Open the Meter Monitor (Detailed) view and

verify the meter is acquiring data, the transducers have good signals and flow
profiles for the chords are displayed and run the Zero Flow Calibration Wizard;
select the

Calibrate

→

Zero Calibrate menu

and generate the report. Then, collect

and save a Maintenance log to show the “as left” condition of the meter. Or use
AMS

™

Device Manager or a HART

®

Field Communicator and select

Overview

→

Zero Calibration

→

Start menu

or

Service Tools

→

Maintenance

→

Zero

Calibration

→

Start

.

9. Close your application connection (MeterLink, AMS

™

Device Manager or HART

®

Field Communicator).

10. If you are not replacing other electronics, replace the end caps and security latches

(requires a 3 mm Allen wrench).

Maintenance and Troubleshooting Manual

Meter maintenance

00809-0100-3812

April 2022

Rosemount 3812 Liquid Ultrasonic Flow Meter

93

«
...
91
92
93
94
95
...
»

Summary of Contents for Rosemount 3812





































































































































Reviews:

No comments

Related manuals for Rosemount 3812

Brand: Keithley Pages: 48

Brand: MadMan Pages: 37

Brand: MADDALENA Pages: 5

Brand: QuantAsylum Pages: 70

Brand: Radio Shack Pages: 44

Brand: Radiodetection Pages: 2

Brand: Keithley Pages: 31

Brand: Keithley Pages: 63

Brand: Keithley Pages: 18

Brand: Keithley Pages: 73

Brand: PCB Piezotronics Pages: 17

Vortex Flow Industry

Brand: Grundfos Pages: 16

Brand: Spacelabs Pages: 156

Brand: Omega Pages: 20

Brand: PASCO Pages: 4

DELMHORST J-2000

Brand: ABQ Industrial Pages: 4

Brand: General Pages: 12

iNELS Air AirCFS-100S

Brand: Elko Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands