Emerson Rosemount 2240S Reference Manual Download | Manualshive

Page: 25 / 194

background image

15

Reference Manual

00809-0100-2240, Rev DA

October 2017

Rosemount 2230 Graphical Field Display

The Rosemount 2230 Graphical Field Display presents inventory tank gauging data such as level,
temperature, and pressure. The four softkeys allow you to navigate through the different menus to
provide all tank data, directly in the field. The Rosemount 2230 supports up to 10 tanks. Up to three
Rosemount 2230 displays can be used on a single tank.

Rosemount 644 Temperature Transmitter

The Rosemount 644 is used with single spot temperature sensors.

Rosemount 3051S Pressure Transmitter

The Rosemount 3051S series consists of transmitters and flanges suitable for all kinds of applications,
including crude oil tanks, pressurized tanks and tanks with / without floating roofs.

By using a Rosemount 3051S Pressure Transmitter near the bottom of the tank as a complement to a
Rosemount 5900S Radar Level Gauge, the density of the product can be calculated and presented. One
or more pressure transmitters with different scalings can be used on the same tank to measure vapor
and liquid pressure.

Rosemount 2180 Field Bus Modem

The Rosemount 2180 Field Bus Modem (FBM) is used for connecting a TankMaster PC to the TRL2
communication bus. The Rosemount 2180 is connected to the PC using either the USB or the RS232
interface.

Emerson Wireless Gateway and Emerson Wireless 775 THUM

™

Adapter

An Emerson Wireless 775 THUM Adapter allows wireless communication between a Rosemount 2410
Tank Hub and an Emerson Wireless Gateway. The gateway is the network manager that provides an
interface between field devices and the TankMaster inventory software or host / DCS systems.

See the Rosemount Tank Gauging System Data Sheet (Document No. 00813-0100-5100) for more
information on the various devices and options.

«
...
23
24
25
26
27
...
»

Summary of Contents for Rosemount 2240S



































































































































































































Reviews:

No comments

Related manuals for Rosemount 2240S

Brand: Harris Pages: 162

Brand: Vega Pages: 20

Wireless Room Temperature Transmitter

Brand: BAPI Pages: 2

Brand: Net Safety Pages: 50

Brand: Teleco Pages: 2

Brand: Evikon Pages: 4

FT-450 - CAT OPERATION REFERENCE BOOK

Brand: Yaesu Pages: 18

Brand: Datcon Pages: 24

Brand: Rover Pages: 27

Brand: HOLATRON SYSTEMS Pages: 12

Brand: Kramer Pages: 12

Brand: JUMO Pages: 3

Brand: M-system Pages: 2

Brand: Marmitek Pages: 2

Evolution EVOIPLITE

Brand: Vanco Pages: 12

Brand: nedis Pages: 80

Brand: RCF Pages: 4

MR HH500 FLT BT

Brand: Cobra Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands