Emerson Rosemount 2240S Reference Manual Download Page 111

Page: 111 / 194

101

Reference Manual

00809-0100-2240, Rev DA

Configuration/Operation

October 2017

Configuration/Operation

Classic view

The Classic View gives you access to the different F

OUNDATION

fieldbus blocks. Also

Mode Summary

and

Factory Reset

and

Restart

is available from this window.

The

Resource Block

contains diagnostics, hardware, electronics, and mode handling information. There

are no linkable inputs or outputs to the Resource Block.

The

Main Transducer Block

contains parameters for configuration of the Rosemount 2240S . It contains

device information including diagnostics and the ability to configure, set to factory defaults and restart
the Rosemount 2240S.

The

Average Temperature Transducer Block

contains parameters for configuration of average

temperature calculations for the Rosemount 2240S Multi-Input Temperature Transmitter for use in a
F

OUNDATION

fieldbus system.

The

Register Transducer Block

allows a service engineer to access all database registers in the device.

Summary of Contents for Rosemount 2240S



































































































































































































Search results

Summary of Contents for Rosemount 2240S

Reviews:

Emerson Rosemount 2240S, Reference Manual, Page: 111 / 194

Search results

Summary of Contents for Rosemount 2240S

Reviews: