Emerson Rosemount 2240S Reference Manual Download

Page: 101 / 194

Reference Manual

00809-0100-2240, Rev DA

Configuration/Operation

October 2017

Configuration/Operation

6. Click the

Change

button and set the device to

Out Of Service

(OOS) mode. In case you don’t change

device mode now, it will automatically switch to Out Of Service when starting the Measurement
Setup wizard.

7. Click the

Guided Setup

button to open the Guided Setup window.

8. Click the desired sensor setup button to start the configuration wizard. The

Temperature / Water

Level

Sensor

Setup

wizards facilitate configuration of the device for most common applications. The

wizard will put the device in

Out of Service

mode until the wizard is finished. See the

Configure/Manual Setup option for access to an extended range of configuration parameters.

Summary of Contents for Rosemount 2240S



































































































































































































Search results

Summary of Contents for Rosemount 2240S

Reviews:

Related manuals for Rosemount 2240S

Brands by name

Popular brands

Emerson Rosemount 2240S, Reference Manual

Search results

Summary of Contents for Rosemount 2240S

Reviews:

Related manuals for Rosemount 2240S

Brands by name

Popular brands