Emerson Rosemount 2240S Reference Manual Download

Page: 100 / 194

Reference Manual

00809-0100-2240, Rev DA

Configuration/Operation

October 2017

Configuration/Operation

5.15

Configuration using AMS Device Manager

The Rosemount 2240S supports DD Methods to facilitate device configuration. The following
description shows how to use the AMS Device Manager application to configure the Rosemount 2240S in
a F

OUNDATION

fieldbus system. For more information on configuration parameters see

“Basic

configuration” on page 50

5.15.1

Starting the Guided Setup

To configure the Rosemount 2240S in AMS:

1. From the Start menu; open the AMS Device Manager application.

2. Open the View > D evice Explorer.

3. Double-click the FF network icon and expand the network node to view the devices.

4. Right-click or double-click the desired gauge icon to open the list of menu options:

5. Choose the

Overview

option.

Summary of Contents for Rosemount 2240S



































































































































































































Search results

Summary of Contents for Rosemount 2240S

Reviews:

Related manuals for Rosemount 2240S

Brands by name

Popular brands

Emerson Rosemount 2240S, Reference Manual

Search results

Summary of Contents for Rosemount 2240S

Reviews:

Related manuals for Rosemount 2240S

Brands by name

Popular brands