Emerson Rosemount 2051 Reference Manual Download Page 119 | Manualshive

Page: 119 / 228

background image

109

Reference Manual

00809-0100-4107, Rev BA

Appendix A: Specifications and Reference Data

April 2013

Appendix A: Specifications and Reference Data

A.2.13

Damping

4-20 mA HART

2051 with Selectable HART

Analog output response to a step input change is user-enterable from 0.0 to 60 seconds for one
time constant. This software damping is in addition to sensor module response time.

2051

Analog output response to a step input change is user-selectable from 0 to 36 seconds for one
time constant. This software damping is in addition to sensor module response time.

A.3

Physical specifications

A.3.1

Electrical connections

1

/

2

–14 NPT, G

1

/

2

, and M20 × 1.5 conduit.

A.3.2

Process connections

Rosemount 2051C

1

/

4

–18 NPT on 2

1

/

8

-in. centers

1

/

2

–14 NPT and RC

1

/

2

on 2-in.(50,8 mm), 2

1

/

8

-in. (54,0 mm), or 2

1

/

4

-in. (57,2 mm) centers

(process adapters)

Rosemount 2051L



High pressure side: 2-in.(50,8 mm), 3-in. (72 mm), or 4-in. (102 mm), ASME B 16.5
(ANSI) Class 150 or 300 flange; 50, 80, or 100 mm, DIN 2501 PN 40 or 10/16 flange



Low pressure side:

1

/

4

–18 NPT on flange,

1

/

2

–14 NPT on process adapter

Rosemount 2051T



1

/

2

–14 NPT female



G

1

/

2

A DIN 16288 Male (available in SST for Range 1–4 transmitters only)



Autoclave type F-250-C (Pressure relieved 9/16–18 gland thread;

1

/

4

OD high pressure

tube 60° cone; available in SST for Range 5 transmitters only)

Rosemount 2051CF

For Rosemount 2051CFA, see 00813-01000-4485 Rosemount 485 Annubar

For Rosemount 2051CFC, see 00813-01000-4485 Rosemount 405 Compact Orifice Plate

For Rosemount 2051CFP, see 00813-01000-4485 Rosemount 1195 Integral Orifice

«
...
117
118
119
120
121
...
»

Summary of Contents for Rosemount 2051





































































































































































































































Reviews:

No comments

Related manuals for Rosemount 2051

Brand: Icare Pages: 3

Brand: 3nh Pages: 10

Brand: Kane Pages: 16

Brand: Kane Pages: 60

Brand: OHAUS Pages: 84

Brand: Hardy Barth Pages: 27

Brand: Zeversolar Pages: 35

Brand: Zenner Pages: 52

Brand: Magnescale Pages: 8

Brand: M-Sure Pages: 2

Brand: Lutron Electronics Pages: 20

Brand: Rion Pages: 4

Brand: H. HERMANN EHLERS Pages: 40

Brand: Van Walt Pages: 2

Brand: Circutor Pages: 48

Stream Line Pro

Brand: Halo Photonics Pages: 45

Stubby LED-1500

Brand: Dive Perfect Pages: 4

Liebert MBX Busway

Brand: Vertiv Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands