manualshive.com logo in svg

Emerson Liebert GXT4-10000RT208, User Manual, Page: 28 / 80

Share
Download
Emerson Liebert GXT4-10000RT208 User Manual Download Page 28

Installation

Liebert

®

 GXT4

™

 User Manual

20

2.5 External Battery Cabinet Installation

Optional Liebert external battery cabinets may be connected to the UPS to provide additional battery run 
time. External battery cabinets are designed to be placed on one side of the UPS in a tower configuration 
or stacked beneath the UPS in a rack configuration. 

Figure 2-4  External battery cabinets connected to GXT4

1. Inspect the external battery cabinet for freight damage. Report damage to the carrier and your local 

dealer or Emerson representative.

2. Optional rack-mount hardware is shipped with the external battery cabinet and may be installed at this 

time if desired.

• Securing hardware and slide rails are sold separately. Please contact your local dealer or Emerson 

representative for these additional options and any assistance needed. Fasten the slides into 
position with the screws per the instructions included with the slide rails.

3. Use the enclosed support bases for the tower option to prevent tip-over. One additional set of support 

base extensions ships with each external battery cabinet.

4. Verify the External Battery Cabinet breaker is in the Off position.

5. Connect the supplied external battery cabinet cable to the rear of the external battery cabinet, then to 

the rear of the UPS.

6. Turn the External Battery Cabinet breaker to the On position.

!

WARNING

Risk of electric shock. Can cause injury or death.
Disconnect all local and remote electric power supplies before working within.
Ensure that the Liebert GXT4 is shut down and power has been disconnected before beginning 
any work on or in the unit.

!

CAUTION

The external battery cabinet(s) are heavy (see 

Table 8-3

). Take proper precautions when lifting 

them.

Cable connects battery 

cabinet

GXT4

Battery Cabinet

Second connector permits adding 

more battery cabinets to 6000VA 

Liebert GXT4

Summary of Contents for Liebert GXT4-10000RT208

















































































Reviews:

No comments