manualshive.com logo in svg

Emerson Liebert GXT4-10000RT208, User Manual

Share
Download
Emerson Liebert GXT4-10000RT208 User Manual Download Page 25

Installation

17

Liebert

®

 GXT4

™

 User Manual

2.0 Installation

Do NOT attempt to start the UPS, turn on any circuit breaker or energize the input power until instructed to 
do so in 

4.2 - Starting the UPS

.

2.1 Unpacking and Inspection

Unpack the UPS and conduct the following checks:

• Inspect the UPS for shipping damage. Report any shipping damage to the carrier and your local dealer 

or Emerson

®

 representative immediately.

• Check the accessories against the delivery list. If there is any discrepancy, contact your local dealer or 

your Emerson representative immediately

2.2 What’s Included

The Liebert GXT4 is shipped with the following items:

• Terminal Block Communication terminals

• Compact Disk with

• Liebert MultiLink

®

• Configuration program

• User manual (electronic version)

• Liebert IntelliSlot

®

 Web card (IS-WEBCARD), factory-installed

• USB cable, one; 1.2 m (3.9 ft.)

• Rack mounting hardware including screws, handles, and rack slide kit

• Power Distribution Box, installed on Liebert GXT4

• Support base set, one

• Warnings, Safety Instructions booklet and WEEE recycling sheet (ISO 14001 compliance)

!

CAUTION

The UPS is heavy (see 

8.0 - Specifications

). Take proper precautions when lifting or 

moving it.

NOTE

The GXT4 External Battery Cabinet shipping package includes one battery cabinet, two spacers 
for tower configuration, one DC power cable and rack mounting hardware, including screws, 
handles and mounting rail kit.

Summary of Contents for Liebert GXT4-10000RT208

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands