manualshive.com logo in svg

Emerson FloBoss 103, Instruction Manual

Share
Download
Emerson FloBoss 103 Instruction Manual Download Page 23

FloBoss 103/104 Instruction Manual 

Revised August-2017 

General Information 

1-17 

▪

 

EIA-485 (RS-485) communications (Comm 1) terminations   

▪

 

RTD input terminations  

▪

 

Optional I/O and terminations  

▪

 

Remote charge terminations  

▪

 

Optional Comm 2 terminations   

1.4.2 

Processor and Memory 

The FB100-Series derives processing power from a 32-bit 
microprocessor. The 32-bit CMOS microprocessor features dual 32-bit 
internal data buses and a single 8-bit external data bus. The unit can 
address up to 4 MB of memory, including high-speed direct memory 
access. 

The FB100 has 512 KB of static random access memory (SRAM) for 
storing interrupt vectors, Proportional, Integral, and Derivative alarms, 
events, and history data.  

The FB100 also has a 2 MB flash memory chip for storing the operating 
system factory code, configuration parameters, and User C programs.  

1.4.3 

Liquid Crystal Display 

An optional two-line Liquid Crystal Display (LCD) panel mounts on the 
Battery Charger module.  

The LCD allows you to view the current and past gas volumes on site 
without requiring a PC. The LCD provides you a visual indication of the 
status of the meter run by displaying the historical performance data to 
help ensure the health and integrity of your installation. 

The LCD panel remains on at all times when the power is applied in the 
valid operating range. The panel cycles its display through a configured 
list of up to 16 parameter values, with the first seven being pre-
configured. The first three displays show values for time, date, and 
battery condition and cannot be configured. The next five displays show 
certain flow parameters and are factory configured, but you may change 
their configuration. 

To configure the list of values for the LCD panel, refer to the LCD User 
List Setup procedure in the 

ROCLINK 800 Configuration Software User 

Manual

 (Part D301159X012).   

1.4.4 

Communications Ports 

The FB100 provides two standard and one optional communication 
ports: 

▪

 

Standard Operator interface port EIA-232 (RS-232) – LOI. 

▪

 

Standard EIA-485 (RS-485) Communications – Comm 1.  

▪

 

Optional EIA-232 (RS-232), or Dial-up Modem Communications – 
Comm 2.  

Summary of Contents for FloBoss 103











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands