manualshive.com logo in svg

Emerson FloBoss 103, Instruction Manual

Share
Download
Emerson FloBoss 103 Instruction Manual Download Page 14

FloBoss 103/104 Instruction Manual 

1-8 

General Information 

Revised August-2017 

(DVS) or a Pulse Interface module.  Three diagnostic analog inputs (AI) 
monitor the battery voltage, logical voltage, and enclosure/battery 
temperature. Refer to 

Chapter 4, Input/Output

. 

Communications 

The Local Operator Interface (LOI) port provides a direct, local link 
between the FB100-Series and a PC through a Local Operator Interface 
cable using EIA-232 (RS-232) communications.  

The Comm 1 allows EIA-485 (RS-485) serial communication protocols.  

The optional communications card for EIA-232 (RS-232), EIA-485 
(RS-485), or dial-up modem activate Comm 2. Refer to 

Chapter 5, 

Communications

. 

ROCLINK 800 

Configuration 

Software 

The PC-based ROCLINK 800 configuration software enables you to 
configure and access the I/O parameters, DVS inputs, flow calculations, 
power control, security, and FST programs. Refer to the 

ROCLINK 800 

Configuration Software User Manual

 (Part D301159X012)  for details 

concerning software capabilities. 

The PC communicates with the FB100-Series through an LOI cable 
using EIA-232 (RS-232) communications.  

1.2.3 

Firmware 

The firmware contained in flash ROM on the processor module 
determines the functionality of the FB100 and includes:  

▪

 

1992 AGA-3 flow calculations (with user-selectable AGA8 
compressibility Detail, Gross I, or Gross II) for a single meter run  

▪

 

1996 AGA-7 flow calculations (with user-selectable AGA8 
compressibility) for a single meter run. 

▪

 

Memory logging of 240 alarms and 240 events  

▪

 

Archival of minute data from the last 60 minutes for up to 35 points 
(Standard History)  

▪

 

Archival of 35 days of hourly data for up to 35 points (Standard 
History)  

▪

 

Archival of 35 days of daily data for up to 35 points (Standard 
History). 

▪

 

Archival of Min / Max historical data for today and yesterday 
(Standard History)  

▪

 

Archival of 5040 entries for up to 15 points at user-specified interval 
(Extended History)  

▪

 

Power control (wake up on ring) on optional internal modem  

▪

 

Logic and sequencing control using a user-defined Function 
Sequence Table (FST)  

▪

 

Closed-loop (PID) control capabilities (requires optional I/O 
termination points)  

▪

 

Communications based on the ROC protocol or Modbus slave, or 
optional host, (ASCII or RTU) protocol for use with EFM 
applications  

Summary of Contents for FloBoss 103











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands