background image

Instruction Manual

D103752X012
September 2020

T208 Series

T208 Series Tank Blanketing Vapor  

Recovery Regulators

Table of Contents

Introduction ..................................................................1
Specifications ..............................................................2
Principle of Operation ..................................................2
Installation ...................................................................4
Startup, Adjustment and Shutdown .............................5
Maintenance ................................................................6
Parts Ordering .............................................................8
Parts List......................................................................9

 

 WARNING

Failure to follow these instructions or 

to properly install and maintain this 

equipment could result in an explosion, 

fire and/or chemical contamination 

causing property damage and personal 

injury or death.
Fisher™ Vapor Recovery regulators must 

be installed, operated, and maintained 

in accordance with federal, state and 

local codes, rules and regulations, and 

Emerson Process Management Regulator 

Technologies Inc. (Emerson) instructions.
If the regulator discharges process 

fluid or a leak develops in the system, 

service to the unit may be required. 

Failure to correct trouble could result in 

a hazardous condition.
Call a qualified service person to service 

the unit. Installation, operation and 

maintenance procedures performed 

by unqualified person may result 

in improper adjustment and unsafe 

operation. Either condition may result in 

equipment damage or personal injury. 

Only a qualified person shall install or 

service the T208 Series vapor  

recovery regulator.

Introduction

Scope of the Manual

This Instruction Manual provides instructions for 

installation, startup, maintenance and parts ordering 

information for the T208 Series vapor recovery 

regulators. Instructions and parts list for other 

equipment used with these regulators are found in 

separate manuals.

Figure 1.

 Type T208 Tank Blanketing Vapor Recover Regulator

Summary of Contents for FISHER T208 Series













Reviews: